120kW Dual Gun DC Fast Charger CCS1 CCS2 CHAdeMO GB/T 200-1000V Output for Public Parking Lot

A floor mounted dual gun DC fast charging station that takes three phase 380V AC input and delivers a stable DC output of 200V to 1000V. One cabinet carries CCS1, CCS2, CHAdeMO and GB/T connectors, so a single unit serves imported European and American EVs together with domestic GB/T models. The 120kW power pool is shared intelligently between the two guns, which keeps utilisation high on busy public parking sites without paying for a second cabinet.

The CLF-DC-120KW-D is built for operators who need a dependable mid power fast charging point with low maintenance. Power modules work in parallel and a single module fault does not stop the station, so charging continues at reduced output until service. The cabinet is rated IP55 and validated from -40°C to +60°C, covering cold northern winters, humid coastal cities and hot inland summers without derating surprises.

Commissioning is handled through OCPP 1.6J over 4G, Ethernet or WiFi, which means the station can join an existing charging management system in hours rather than weeks. Drivers start a session with an RFID card, a QR code scan, VIN recognition, the mobile APP or a remote command from the CMS, and every transaction is reported back to the operator platform for billing and statistics.

• Dual gun 120kW output with intelligent power sharing. The station allocates 60kW to each gun when two vehicles charge together, or releases the full 120kW to a single vehicle for the shortest possible session.
• Four connector standards in one cabinet. CCS1, CCS2, CHAdeMO and GB/T cover almost every DC fast chargeable EV on the road today, removing the need for separate stations per standard.
• DC 200V to 1000V wide output range. The same unit charges 400V class passenger cars and the new 800V high voltage platforms without extra hardware or firmware changes.
• Three phase five wire AC 380V ±15% input. Both 50Hz and 60Hz grids are supported, and the power factor reaches 0.99 for lower energy loss and smaller utility penalties.
• Five start methods for commercial flexibility. RFID card, QR code scan, VIN recognition, mobile APP control and CMS remote start or stop can be combined per site policy.
• OCPP 1.6J with multi network connectivity. Built in protocol support plus 4G, Ethernet and WiFi channels allow fast integration with mainstream charging operators and roaming platforms.
• 10 inch high brightness colour touch screen. The interface stays readable under direct sunlight and guides the driver through plug, pay and charge steps without staff assistance.
• Air cooling architecture. No liquid cooling loop means fewer service routines, simpler spare parts and reliable long hour continuous operation.
• Wide climate tolerance. Operating range of -40°C to +60°C and IP55 ingress protection allow permanent outdoor floor installation.
• Full electrical protection set. Short circuit, over temperature, over current, leakage, over voltage and under voltage protection act at module and system level.
• TUV, CE and FCC certification. Documentation is ready for European and North American market access and tender submission.
• 5m charging cable as standard. Extra reach gives drivers freedom when parking position is not ideal, and longer cables are available on request.
• OEM and ODM service. Housing colour, logo, connector mix, output power allocation and firmware wording can be configured to project specification.
• Low total cost of ownership. Mid power modules, air cooling and single module replacement keep spare parts stock small and service visits short.

The enclosure is formed from galvanised sheet steel with a powder coated outer skin, and the door layout separates the power compartment from the control compartment so routine inspection does not expose live DC busbars. Internal layout follows a front to back airflow path: cool air enters through filtered louvres, passes the power modules and exits at the top, which keeps module temperature stable during continuous operation.

Cable management is handled by a weighted retractor or a hook bracket, and the connector holster is positioned at comfortable reach height. Every unit is factory tested with a resistive load bank across the full output range before packing, and the test record is supplied with the shipping documents for site acceptance.

• Public parking lots, shopping centre car parks and retail plazas that need a compact two vehicle fast charging point.
• Highway service areas and rest stops where a 30 to 40 minute top up has to fit a travel break.
• Commercial and industrial parks serving staff, visitors and corporate EV fleets.
• Taxi, ride hailing and light logistics depots that recharge vehicles between shifts.
• Hotel, hospital and airport parking facilities adding destination fast charging.
• Municipal and community charging points in residential districts.
• Car dealerships and service workshops that need in house DC charging for delivery and testing.
• Fleet yards where one cabinet must serve mixed brand vehicles from different markets.

Each station ships with TUV, CE and FCC certification copies, which supports customs clearance, utility approval and public tender documentation in most overseas markets. The standard warranty covers 24 months on the complete unit and 12 months on consumable parts such as cables and connectors, with extended coverage available for framework projects.

Spare power modules, control boards, displays and connector assemblies are held in stock, so replacement parts can usually be dispatched within one week. Remote diagnostics through the CMS platform allow our engineers to read fault codes, module status and charging logs before a site visit, which shortens downtime and avoids unnecessary travel.

Send us your site power capacity, the connector combination you need, expected daily sessions and whether a CMS platform is already in place. Our engineering team will return a matched configuration, a cable and foundation drawing, and a quotation with delivery schedule. Sample orders and OEM projects are both welcome, and we can support your tender documentation with certificates, test reports and technical datasheets.

Specifications are subject to project configuration. Please confirm the final connector mix, cable length and interface language before ordering.